Options

• Line switch

  The M8010 connects between the voice terminal and the line cord from the PBX. This allows the recorder audio to use existing spare conductors in the line cord. The switch connects the recorder audio to pair 1 on a 4-wire voice terminal, and pair 2 on a 2-wire voice terminal.
  It is important to set this option before plugging the line cord into the voice terminal.

  

  
  

• Jumpers

  Two jumpers are located on the M8010. Both JP1 and JP2 are factory set and are only accessible from inside the voice terminal.

• JP1

  JP1 selects the type of voice terminal the M8010 is installed in.

  1. Position "A" is used for 8410 voice terminals.
  2. Position "B" is used for 8434 voice terminals.

• JP2

  JP2 determines how the beep tone operates.

  1. Position "A" causes the module to generate a beep tone every 15 seconds.
  2. Position "B" causes the module to generate a beep tone when it detects a beep tone being generated by the recorder.

  Position "B" is the factory default setting for JP2.

Connection Tables

The following tables show the wiring for the M8010.

• Circuit pack connections: 2-wire port

  Use this table when connecting to a 2-wire port circuit pack.
  The recorder audio connections are shown in bold.

  DESIGNATION	PIN # ON NEW MODULAR LINE JACK	TYPICAL 103 OR 104 BLOCK #	DEFINITY STATION WIRING CODE		PAIR
  Analog audio output for recorder (T)	1	3	white/orange		2
  Analog audio output for recorder (R)	2	4	orange/white		2
  none	3	5	white/green		3
  Ring (R)	4	2	blue/white		1
  Tip (T)	5	1	white/blue		1
  none	6	6	green/white		3
  -48vdc	7	7	white/brown		4
  GRD	8	8	brown/white		4

• Circuit pack connections: 4-wire port

  Use this table when connecting to a 4-wire port circuit pack.
  The recorder audio connections are shown in bold.

  DESIGNATION	PIN # ON NEW MODULAR LINE JACK	TYPICAL 103 OR 104 BLOCK #	DEFINITY STATION WIRING CODE		PAIR
  Terminal transmit tip (TXT)	1	3	white/orange		2
  Terminal transmit ring (TXR)	2	4	orange/white		2
  Private branch exchange transmit tip (PXT)	3	5	white/green		3
  Analog audio output for recorder (R)	4	2	blue/white		1
  Analog audio output for recorder (T)	5	1	white/blue		1
  Private branch exchange transmit ring (PXR)	6	6	green/white		3
  -48vdc	7	7	white/brown		4
  GRD	8	8	brown/white		4

• Internal connection reference

  A 14-conductor ribbon cable plugs into a header on the M8010 and connects to the voice terminal main printed wiring board. The connections are included here for reference:

  PIN	NAME	DESCRIPTION	PIN	NAME	DESCRIPTION
  1	GRD	Ground	8	HR	Handset receive audio
  2	HT	Handset transmit	9	AX	Aux logic
  3	HS	Handset logic	10	SR	Speakerphone audio
  4	ST	Speakerphone transmit	11	nc	---
  5	SP	Speakerphone logic	12	AR	Aux audio
  6	AT	Aux transmit	13	nc	---
  7	SPC	Speakerphone multiplex logic	14	PWR	+5vdc

Specifications

M8010
GENERAL	Size	4.18"L x 2.93"W x 0.5075"H
	Weight	2.2oz
	Operating voltage	5vdc, internal
	Power consumption	9mA
AUDIO	Audio output	-0dB Loss (+-1dB)
	Beep tone	1400Hz; 200ms burst; 12-15 sec. interval
	Insertion loss	Less than .5dB